If you look at the paper label on the top of the drive you will find a diagram for the jumper placement. I really appreciate it that you stuck with this thread for so long and helped me so much. In this case, I would make only two partitions on the 40gb drive, the second one a lot smaller, Windows and all programs on the first partition. The four item in the list appears to be the correct file. Try booting with the SeaTools diagnostics CD again. Quality Polaroid Lens from brand makers. First I should clarify what a system disk is.
|Date Added:||20 February 2013|
|File Size:||39.48 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Can the circuits on the floppy drive’s board fry if the DATA connectors are the wrong way around, or will it then just cause the LED on the mss of the floppy drive to be on all the time the computer is running I do not presently have that problem? These are primarily portable versions of Linux. The second one motherbkard a bootable CD. Landing Zone Cylinder location of the landing zone. You may have noticed SeaTools displays the total number of hours the drive has been used might not apply for the 6.
OtheHill, In response to Seagate has two of those to choose from, MaxBlast and another one, if at least one hard drive connected to the computer is the Seagate or Maxtor brand. You have 30 days to Activate Windows unless your Product Key is found to be one of the ones Microsoft knows is being used illegitimately, after you have allowed the Windows Genuine Advantage program to be loaded and to run, in which case, you can NOT Logon into Windows itself until you DO have a valid Product Key.
Thanks so much for all the other answers and information! In the second stage of Setup, Windows detects devices and installs drivers; it installs generic drivers for most things if it doesn’t have specific ones.
What can be accomplished by running the fitness utility. MS ver 1 drivers. When I turned on the system I heard and saw the two fans spinning, but I heard no beeps, only “clickety-click-wrrrrrrrrrrrr” which I guess is the CD WR drive.
MSI 845GEM (MS-6714)
In that case, you must either run a Repair installation of Windows, or the poor second choice is, you install Windows from scratch. You have motuerboard me learn much since I started this thread. If there are still spare good sectors available when you zero fill the drive, then the drive will pass the zero fill procedure, and no errors will be found when you run the long test again.
If the cable is ripped at either edge, it’s often right at a connector where it’s supposed to connect to the contact in the connector where it’s pressed into the 67114, where it’s hard to see, motherboars if there is a cable clamp piece over the cable at the connector the end connectors usually have that – the middle connector may not. Only larger brand name system builders e. Do you see any sign of life on the monitor?
This page contains information about installing the latest More information. You may need to enter the parameters manually. Over a Month Ago Time Zone: So I wondered whether the problems lied with my floppy disks or not. I mothetboard had an idea only now – my MSI4 has a floppy drive in it!
Page Up or Page Down – select Auto If that wasn’t right, you need to change itand you may need to Save bios settings, the computer will boot, then go back into the bios Setup. There are 6 MS mboard version series http: If your Boot Order or similar motherboqrd are set so the floppy drive is listed first in the bios Setupthat should work fine. Is the above 40G hard drive compatible with the MS?
Or, you set the drive to Master, Single – you motherbard no jumper on the drive when it’s by itself on the Primary data cable connection, and you connect the optical drive to the secondary IDE header and jumper it as Master, or you jumper both drives Cable Select, an have them on the end connector, not the middle connector, on a 3 connector data cable, when they’re by themselves on the data cable.
Help me resurrect a throw-away MS VER:1
Yay, this time there was life on the monitor up to the following point: IMO there are better brands available. Without going back through the thread did you verify you even have a hard drive installed. No mothrboard beep anymore, I’m assuming.
I read the name Phoenix Bios D, checked the beep codes at the link http: What should I do next?